A door-position sensor, often called a door contact, tells an access control system whether a door is physically open or closed. That is door state. It is separate from lock state, which is whether the lock is holding or released, and from the credential decision, which is whether a card or code was allowed or denied. The sensor reports position only. It does not lock anything or confirm the door is secured.

How a door contact knows the door moved

A door-position sensor has two pieces. One mounts on the door and the other on the frame, lined up so they sit side by side when the door is shut. In a common arrangement, one piece is a small magnet and the other is a switch that changes state when the magnet is near it. When the door swings open, the pieces separate, the switch changes, and the controller (the unit that makes the access decisions) sees the door go from closed to open. When the door shuts, it sees the change back.

Some contacts sit on the surface, usually as a small block near the top of the door. Others are recessed into the door edge and the frame, so with the door open you only notice two small round faces.

Without a door-position sensor, the access control system knows only what it did itself. It knows a card was accepted and the lock was released for a short time. It does not know whether anyone actually pulled the door open, or whether the door swung shut afterward.

A closed door is not proof of a locked door

The most common mix-up is treating the door-position sensor as part of the lock, or as a sign the door is secured. It is neither. The sensor watches the gap between door and frame. It has no idea whether a latch or bolt is engaged. Each part at an access-controlled door has its own job:

  • Reader: takes the credential, such as a card or code.
  • Controller: decides whether that credential is allowed at this door right now.
  • Lock: holds the door or releases it.
  • Door-position sensor: reports whether the door is open or closed.

A door can rest closed in its frame with the latch not caught, or with the lock still released, and the sensor will report it closed. Some systems take a separate signal from the lock to report lock state, but that is a different input from the door contact. How the other three parts pass a decision along is its own topic. The point here is narrower: position is not security.

Can an access control system tell if a door is propped open?

An access control system can flag a propped door if it has a door-position sensor and is set up to watch for it. Door state lets the system answer questions it otherwise can't.

Was the door left open too long?

If the door opens after a valid entry and stays open past a set time, the system can treat it as held open. That is how a propped door shows up in the record instead of going unnoticed until someone walks past.

Did the door open without a credential?

If the sensor reports the door opening when no card was accepted and the lock was never released, the system can log a door opened without authorization. Many setups also take a signal from an exit button or exit hardware so people leaving don't show up the same way.

Did the door close after someone came in?

A valid entry followed by the door shutting is the normal pattern. A valid entry with no close afterward is worth knowing about, especially on a street door or a storage room.

What a particular system does with these events depends on its configuration. One only writes them to a log. Another shows a notice or sends a message to whoever is responsible. Treat them as things to ask about rather than features you can assume.

Deciding which doors should report their state

For each door, the question that matters is what you would do differently if you knew it was open. Bring questions like these to a conversation about your doors:

  1. Which doors would cause a real problem if left open, and which can go unmonitored?
  2. Does the existing door and frame have room for a contact, and how would a wire reach the frame?
  3. Who should hear about a held-open door or a door opened without a credential, and how soon do they need to know?
  4. Do you want records kept for later review, or does a live notice matter more?

The door itself matters too. A door that sags or doesn't close fully on its own will keep reporting open, and a contact can't fix that. Sorting out the closer or hinges is door hardware work, and it comes before the sensor's reports mean much.

If you are planning access control for a building in Midtown Manhattan or anywhere in the five boroughs, you can call Imperial Locksmith & Security at (917) 500-1145 to talk through which doors you want watched.

Frequently asked questions

Does a door-position sensor work on any kind of door?

Door-position sensors come in surface-mounted and recessed styles, so most swinging doors can take one in some form. Glass doors, pairs of doors, and doors with a wide or uneven gap to the frame often need a different arrangement, because the two pieces have to line up closely when the door is shut. Which style fits depends on how the door and frame meet when closed.

Is a door sensor the same thing as an alarm?

A door-position sensor is an input, not an alarm. It reports open or closed to the access control system, and the system's setup decides what happens next. Alarm systems use similar contacts, but sharing a part type does not turn an access-controlled door into an alarmed door.

Do I need a door-position sensor on every access-controlled door?

A door-position sensor is most useful on doors where knowing the door is open would change what someone does, such as a street entrance or a room holding equipment or stock. An interior door with a reader may not need one if nobody plans to act on its open or closed status. Decide door by door.

What happens to the door record if the sensor stops working?

When a door-position sensor fails, the system's record of that door stops matching what is really happening. Depending on the fault, the door can appear permanently closed, so a propped door goes unnoticed, or permanently open, so held-open notices keep appearing. The lock and reader generally keep working, since the sensor does not hold the door. A door that shows open while plainly shut is worth having checked.